Can I Set Up A Tub Myself?
Maintenance Sign-UpJust how do you actually feel when it comes to How to Install a Bathtub Yourself?
Mounting a tub isn't exactly rocket science, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old bath tub with a new one is additionally a reasonably hard task. If the old tub is readily available, the project can relocate rapidly; if you have to open up a wall to get rid of the old tub and also place the new bath tub, the job is much harder. In either situation, the project is within a home handyman's abilities, although you will require a helper to vacate the old tub and embeded in the new one. Make certain you have certified yourself for the task and fit trying it. Instead of working with a specialist to take control of a halfway-completed job, it is far better to consider utilizing one prior to you begin. Opportunities are you may need a specialist plumber to make tube links.
This short article will certainly assist you install a brand-new bathtub in your washroom if you have actually already gotten a brand-new tub and also don't require to alter the arrangement of your previous supply of water pipelines.
Your devices and material list ought to consist of the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you need to do is detach the water. After doing so, turn on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite bothersome due to the restricted gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have actually been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any old sealing substance.
Prior to moving on to fit the new taps, contrast the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin making certain that the washing machines remain in place between the tap as well as the sink. Protect the faucet in position with the manufacturer offered backnut. When the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal tap connectors. The former type must be attached to the faucet finishes first, tightening only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Bathtub
Using both wood boards under its feet, put the tub in the needed setting. The wooden boards are useful in evenly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small factors.
The following objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the level as well as changing the feet on the bathtub till the level checks out level.
To mount faucets, fit the bottom of the furthest adaptable faucet port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Activate the water system as well as check all joints and brand-new pipework for leaks and tighten them if essential. Load the tub and likewise inspect the overflow outlet as well as the normal electrical outlet for leaks.
Finally, deal with the bathroom paneling as described in the supplier's user's manual. Tiling and securing around the tub needs to wait up until the bathtub has actually been utilized at least when as this will resolve it right into its final position.
Planning for the Setup
Firstly, the sustaining frame provided with the bath should be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps device to avoid pressure on the bathtub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its final setting.
Tiling Around the Tub
In the location where the bath meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, creating the water to pass through the wall between the bath as well as the tiling, causing difficulties with wetness and also possible leaks to the ceiling below.
You can choose from a range of coloured sealants to assimilate your components and also installations. They are marketed in tubes as well as cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to enable the motion experienced when the tub is in use. The sealant can crack rather very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily available on the marketplace. It is advisable to fit the tiles using water-resistant or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed reading our excerpt on How to Install a Bathtub Yourself. Thanks for taking time to read through our piece of content. So long as you enjoyed our blog post please don't forget to pass it around. We recognize the value of reading our article about How to Install a Bathtub Yourself.
Click For More Information